EM-COM474 · Industrial Communication Board

Dual CAN FD + Dual LIN,
one board, zero adapters.

An STM32G474-based industrial communication board with two CAN FD channels and two LIN channels on rugged screw terminals — 9–36 V input, full ESD protection, and everything you need to build gateways, test ECUs, or sniff buses on the bench.

2 ×CAN FD channels
2 ×LIN channels
9–36 VDC input range
80×60mm board size

Features

Built for the bench and the field

Every design choice targets real automotive and industrial workflows — no dev-board compromises.

MCU

STM32G474 @ 170 MHz

Arm Cortex-M4F with FPU, 512 KB Flash and 128 KB SRAM — hardware FDCAN and LIN-mode USARTs, no bit-banging.

CAN FD

Two CAN FD channels

Classical CAN and CAN FD up to 5 Mbit/s data phase. Industrial transceivers with dedicated ESD arrays on every channel.

LIN

Two LIN channels

LIN 2.x master or slave selectable per channel by jumper — emulate a node or talk to one, on the same board.

POWER

9–36 V industrial input

Reverse-polarity protection, TVS surge clamp and a buck converter with generous 3.3 V budget for add-ons.

RUGGED

Screw-terminal buses

5.08 mm screw terminals for every bus channel — CANH/CANL/GND and LIN/VBAT/GND survive vibration and daily re-wiring.

FLEXIBLE

Termination on demand

Optional 120 Ω CAN termination via solder jumper per channel; LIN master/slave pull-up selectable by header.

DEBUG

SWD + activity LEDs

10-pin SWD header, reset button, BOOT jumper, user LED and per-bus traffic LEDs for instant visual feedback.

EXPAND

GPIO broken out

Remaining MCU pins on 2.54 mm headers — ADCs, timers, SPI/I²C ready for your sensors and actuators.

OPEN

Manufacturing-ready

2-layer design to JLCPCB rules with LCSC-stocked BOM — prototype to small batch without re-spinning.

Specifications

Technical data

Full hardware specification of the EM-COM474.

MCUSTM32G474RET6 · Arm Cortex-M4F @ 170 MHz · 512 KB Flash · 128 KB SRAM · LQFP-64
CAN FD2 × FDCAN (FDCAN1, FDCAN2) · ISO 11898-1:2015 · up to 5 Mbit/s data phase · industrial transceiver per channel · NUP2105L ESD protection · optional 120 Ω termination (solder jumper)
LIN2 × LIN via USART LIN mode · LIN 2.x · TJA1021-class transceiver · master/slave termination jumper per channel
Power input9–36 V DC · 2-pin screw terminal · reverse-polarity protection · SMBJ36CA TVS · buck to 3.3 V, ≥500 mA budget
Bus connectors5.08 mm screw terminals · CAN: CANH / CANL / GND per channel · LIN: LIN / VBAT / GND per channel
Clock8 MHz HSE crystal · load capacitors fitted
Debug10-pin 1.27 mm SWD header · reset button · BOOT jumper · user LED
IndicatorsPer-bus activity LEDs · CAN1/CAN2 (blue) · LIN1/LIN2 (yellow) · 3V3 power · user (green)
Expansion2 × 20-pin 2.54 mm headers · remaining GPIO, ADC, timers, SPI, I²C
Form factor80 × 60 mm, 2-layer · 4 × M3 mounting holes · JLCPCB design rules

Interfaces

Wiring at a glance

Four bus channels, one power inlet — all on pluggable screw terminals.

CAN1 / CAN2

Two independent CAN FD buses. Close the solder jumper for 120 Ω termination at bus ends.

CANH · CANL · GND  |  TERM 120Ω (solder jumper)

LIN1 / LIN2

Two LIN 2.x channels. Set the master jumper to drive the bus, or leave it open to listen as a slave.

LIN · VBAT · GND  |  MASTER / SLAVE (jumper)

POWER

Single 9–36 V DC input feeds the whole board; VBAT can be jumpered to VIN for LIN pull-ups.

VIN · GND  |  VIN→VBAT (solder jumper)

SWD / GPIO

Standard 10-pin SWD for flashing and debugging; two 2.54 mm headers expose the remaining MCU I/O.

SWDIO · SWCLK · 3V3 · GND  |  2 × 20-pin GPIO

Applications

Where it fits

From gateway prototypes to production test jigs.

CAN FD ↔ LIN gateways ECU development & testing Bus data logging Automotive bench prototyping Body electronics (LIN) simulation Industrial automation EOL test fixtures Protocol research & education

Available now

Boards, batches and customization

Evaluation boards, volume pricing and OEM variants (connectors, isolation, enclosure) — tell us about your project.